TRIMMING TOOLS SEE MISCELLANEOUS
********************************
** SMALL AIR COILS
TYPE-26 18x7 mm 26 turns close wound 3 for 1.00
TYPE-15 9x7 mm 15 turns close wound 3 for 1.00
TYPE-8 10x3 mm 8 turns close wound 5 for 1.00
TYPE-6 8x4 mm 6 turns space wound 5 for 1.00
**ROLLER COASTER INDUCTOR
Beautiful ceramic var. inductor 80 µH with gear reduction, very smooth,
silver plated wire, dimensions 16,5x9,5x8,5cm 199.00
**COIL DIY ASSEMBLIES NEOSID
The pitch equals the wellknown Toko 7 mm (can size) 5-pin inductors.
For AL based turns calculations see the formula in the Amidon powdered iron
toroids section or our special calculator in this catalogue software.
**NEOSID 5 mm. series
Consists of: copper can 5x5x8 mm, former, slug. Normal 5-pin (3.5 x 3.5 mm).
5.1 0.5 - 15 MHz 2.25
5.2 15 -200 MHz 2.25
**NEOSID 7 mm. series
Consists of: copper can, 2 section former, threaded core and cup core.
The cup must fit snugly over the plastic former. If necessary use glue or a
rubber filling ring on top. Normal 5-pin (5 x 5 mm).
7A1S 0.1-5 MHz brown (F2) AL(nH)=13 2.25
7F1S 5-15 MHz violet (F10B) AL(nH)=12 2.25
7K1S 15-25 MHz blue (F20) AL(nH)=6.5 2.25
7T1S 20-60 MHz yellow (F40) AL(nH)=5.5 2.25
7V1S 40-200 MHz green (F100B) AL(nH)=4.5 2.25
7V1K 40-250 MHz white (F100) AL(nH)=5.5 low profile h=10mm 2.25
**NEOSID 10 mm. series
Consists of: copper can, 2 section former, threaded core and plastic gasket.
Normal 5-pin.
10A1 0.1-5 MHz brown (F2) 2.75
10F1 5-15 MHz violet (F10B) AL(nH)=6-8 2.75
10K1 8-28 MHz blue (F20) AL(nH)=4-6 2.75
10T1 10-60 MHz yellow (F40) AL(nH)=3-5 2.75
10V1 25-200 MHz green (F100B) AL(nH)=2.5-3.5 2.75
**SPARE NEOSID FORMERS AND CORES
Former 16 x 7 mm, stud on 3 mm 0.57
Former 25 x 6 mm, stud on 2.5mm 0.57
Former 17 x 4 mm, snap-in (core 3.5mm see above 7 and 10 mm kits)
Core M5 for 6 mm former, 5-50 MHz 0.45
**COIL FORMERS, INSULATORS
High voltage insulator ribbed cylinder 130 x 60 mm with 6mm threads 12.90
Hi-Q SW inductors, litz wire or silver plated wire, square baseplate incl.
screws, 70x22 mm, diff. values (winding simply removed) 3.40
same, set van 9 22.24
ditto, 60x15 mm, on baseplate incl. screws 2.95
same, set van 4 11.34
Ceramic coil former with nut, some with core 1.32
Plastic 2-pin 18x5 mm with screw core 0.45
Porcelain insulator rod 2-holes 65x12 mm. 0.36
Mushroom insulator porcelain 25x25h mm round, hole 6,5 mm 0.68
Antenna-insulator high voltage porcelain 32x32 round, 2 screw holes bottom 3.13
Plastic egg insulator 0.50
Cer. former 24x12 diameter. 16 holes for pins 1.25
***************************************************
**READY MADE INDUCTORS
(Many thousands stocked from LF to UHF, SMD too)
NEOSID - TOKO - COILCRAFT
***************************************************
New: Ferrite rod 16cm with MW + LW spoelen 2.25
Neosid ready made stock items:
Unlisted types please call for Toko replacement.
We may also have some old Neosid numbers in small quantities.
All below 5... numbers are 4.50 each, helix inductors are 6.90
5116.31 * yellow 36 nH Helix Q=150 helix
5118.30 red 53 nH Helix Q=150 helix
5146.30 * red 76 nH Helix Q=150 helix
5034 * red-red-black 60 nH (replaced by Toko)
5036
5061 blue-brown 120 nH
5042 * yellow-red 120 nH +tap
5046 yellow-blue 900 nH
5048 yellow-grey 1 µH
5252.30 Toko replace stocked
5840 * -green-violet 1.7 µH
5823 black-black-white 2.5 µH
5056 blue-green 4 µH
5800 brown-grey 8 µH
5089 * white-grey 23 µH
5135 * violet-red-blue 82 µH
5960 * red-red-black 82 µH +tap
5902 * -green-brown 3.3 mH
Cer.spoel Burned-in silver windings 1 µH 30x15mm. 5.40
Special: Helical coil Neosid 9 windings Q=220 max. 600MHz
red copper core, only 10+ 0.45
Special: VHF smd inductors high Q, 5x5mm Toko-style,
5 conn.(wind. 1-3) Q=45
938-250 VCO coil 23 nH (3/4 wdg) 1.34
938-175 VCO coil 32 nH (1 3/4 wdg) 1.34
Further- Large quantities of TV inductors 5.5 (6) and 38.9 (39.5) MHz.
**MURATA HIGH-Q CHOKES SMD
1.5 nH (0603) 1.00
2.5 nH (1210) 1.00
**AIR COILS
**LUCHTSPOELTJES
approx. 1.5 µH 10x3 mm 15 turns 0.75
approx. 750 nH 8x3 mm 8 turns 0.75
approx. 220 nH 10x3 mm 8 turns 0.75
approx. 150 nH 8x4 mm 6 turns 0.75
**HF CHOKES
RF CHOKES many variations and values price for axials 0.70
Toko 8RB (pitch 5mm) 1.25
Toko 10RB (pitch 5mm, magnetic screening) 2.95
2 x 7 mH Siemens common mode choke (mains) round pcb model 2.22
Millen-1535 2.5mH - 160mA high-Q layer choke axial plate choke 7.90
Millen-1540 2.5mH - 500mA high-Q layer choke axial plate choke 12.90
Siemens axial:
3µH-3A axial 2.00
5µH-10A axial 2.00
6µH-4A axial 2.00
7µH-4A axial 2.00
19.5µH-2A axial 2.00
56µH-1.5A axial 2.00
60µH-0.7A axial 2.00
100µH-1A axial 2.00
420µH-0.15A axial 2.00
TDK T TDK T-filter 3-pin 2xL plus 390 pF 0.34
STOCKED IN SMT:
We recently acquired a large quantity of TDK ferrite SMT chokes, ranging
from 10 nH to 100 mH, up to 10 Amps. Please ask!
Standard stock:
SMD sm.sp. SMD choke 4.7,10,15,22,33,47,68,82,100,150,220,330,470 nH
SMD sm.sp. SMD choke 820 nH, 1 µH, 2,2 µH, 4,7µH, 10 µH, 22 µH
SMD sm.sp. SMD choke 100-470 µH
SMD Siemens SMD choke Siemens or TDK E12 from 10nH standard Q 1.13
SMD Pan. SMD choke Panasonic Hi-Q 0402 size E12 values 1 - 18 nH 0.75
SMD hi-Q E12 range 10 t/m 680 nH TDK kigh-Q 1.25
TDK High-Q smd chokes, size 2018 (2.0 x 2.5 mm, h= 1.8 mm)